How to Replace a Bathtub Yourself: Removing and also Replacing.
How to Replace a Bathtub Yourself: Removing and also Replacing.
Blog Article
Every person may have their own unique piece of advice about How to Install a Bathtub Yourself.
Mounting a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is also a reasonably challenging project. If the old tub is conveniently available, the project can move easily; if you need to open a wall to get rid of the old bathtub as well as position the brand-new tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the job and also fit attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might need a professional plumber to make tube links.
This short article will certainly assist you install a brand-new bathtub in your washroom if you have currently purchased a brand-new tub and also don't require to alter the setup of your previous supply of water pipelines.
Your devices and product checklist must comprise the following:
Planning for the Installation
First of all, the supporting framework provided with the bath needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be quite troublesome because of the limited gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
Before proceeding to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in evenly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub till the spirit level reads degree.
To set up taps, fit all-time low of the outermost versatile faucet adapter to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints and also brand-new pipework for leaks and also tighten them if required. Fill the bath tub and also inspect the overflow outlet and also the typical outlet for leakages.
Finally, deal with the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has been made use of a minimum of when as this will resolve it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location between the tap and also the sink. Secure the faucet in position with the producer given backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind needs to be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, causing difficulties with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components as well as installations. They are sold in tubes and cartridges, and are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the motion experienced when the tub is in use. The sealant can crack fairly very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the market. It is recommended to fit the tiles using water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that article about A Step-by-Step Guide to Installing a Bathtub while exploring the search engines. Sharing is good. You won't know, you will be helping someone out. Thank you for taking the time to read it.
Book-Now Report this page